(480) 596-0500
Silver Mazda RX-7 in front three-quarter on red dyno-style rollers in the shop.

Mazda tuning: Mazdaspeed, Miata, RX-7

Mazda is one of the eight makes we stock the full COBB line for, which covers the turbo Mazdaspeed3 and Mazdaspeed6. The Miata is the other half of our Mazda work: suspension, alignment, and sometimes a turbo.

  • MX-5 Miata (NA–ND)
  • Mazdaspeed3
  • Mazdaspeed6
  • RX-7
  • RX-8
  • CX-5 Turbo

Book a Mazda visit(480) 596-0500

Silver Mazda RX-7 in front three-quarter on red dyno-style rollers in the shop.Low close-up of the silver RX-7 nose and hood with a hood vent and the Mazda emblem.Side view of the silver RX-7 front fender and black wheel on steel dyno rollers.Engine bay of the silver Mazda RX-7 with a silver intake tube and a DynoComp plateClose view into the engine bay of the silver Mazda RX-7Tight shot of the DYNOCOMP plate and black air filter beside a silver intake tube.

What we do on each

Mazdaspeed3 and 6

2.3 turbo four. COBB Accessport custom maps written on the dyno, intakes, intercoolers, downpipes, fuel-pump upgrades and E85 blends where supported. The 6 is all-wheel drive and runs on our AWD dyno.

MX-5 Miata

Light and rear-drive. Coilovers, sway bars and a real alignment change the car most. Turbo and supercharger builds get a custom calibration on aftermarket or supported management.

RX-7, RX-8 and swaps

Rotary engines and engine swaps tuned on aftermarket management on the dyno. One review from 2026 describes an RX-7 engine swap in our shop that looks factory-fitted.

Lowered cars need a real setup

A Miata on coilovers with a generic alignment often drives worse than stock. We set camber, caster and toe on our alignment machine to settings that suit your ride height, tires and use, street or track. One owner's review describes exactly that: coilovers fitted elsewhere, a poor alignment, then a car that finally drove right after we set it up.

NA, NB, NC and ND Miatas are all welcome, along with maintenance on older cars.

Miatas and RX cars run on the rear rollers, the Mazdaspeed3 on the front, the Mazdaspeed6 on our AWD dyno with front and rear load controlled. Each driven tire sits between two 8.5-inch rollers, so most cars need no straps. AFR, boost and timing are logged live, and you leave with a printed sheet and the datalog.

Mazda owners on Dyno-Comp

★★★★★

“Literally the coolest place I have ever seen in my life. I was driving and I saw what looked like heaven, a gtr and insane mustangs. I didn’t even spend money here and regardless I walked in and a guy showed me out back and what these guys are doing is magic because how on earth does someone perfectly fit an engine swap an rx7 and make it look like that’s how it came from the factory. These people are pros pros. I even asked them how a tune worked (I’m only 17 and have no idea how it works) and I left knowing exactly what it was. If I ever get a tune this is where I’d want it from easily.”
Parker BuckinghamGoogle review, July 2026

Mazda questions

Do you sell COBB Accessports for the Mazdaspeed3?

Yes. We stock the COBB line for Mazda and custom-tune the map on the dyno.

Can you align my lowered Miata for track days?

Yes, on our alignment machine, to performance settings that suit your ride height and tires.

Do you tune turbo Miatas?

Yes, where the car runs supported or aftermarket management. Tell us the setup.

Model, parts and goal

A tune, a suspension setup or both.

See also: Fiat 124 · performance shop